SSD Sandisk 480GB on Marvell 88SS1074-BSW2

[Marek]

Hello

Any chance to support this marvell controller on short future ?

SSD Sandisk 480GB on Marvell 88SS1074-BSW2

BSY when connect to PC3000 every time

[Roman_TS]

It's new generation of Marvell controllers. In future it would be supported, but 100% not in this 2016 year

[Amarbir[CDR-Labs]]

Source of the post It's new generation of Marvell controllers. In future it would be supported, but 100% not in this 2016 year

BTW Roman,
Can We Have a Update The Bugs We All Have Mentioned In Forums Many Times Soon Please

[studiogsm]

Any news in topic ?

[Ohtic]

Hi Everyone

Any update on this? i have a few in the lab at the moment. All staying busy.

[Roman_TS]

In PC-3000 6.3x developers add Sandisk based on Marvell controllers in support list. But for normal working, we need a new version of terminal - v 3.0, with 1.8 - 3.3V range support. It's under developing now, and without new terminal + some improvements in current software, recovery will be impossible.

[bcasol]

Any updates on this issue ?

[Roman_TS]

Version PC-3000 6.4x is not released yet, as well as Terminal 3.0 adapter. Please, keep to watch our news

[dataq]

Hi Roman,

Any idea when 6.4 will be released. Also will it support this marvel controller.

[Amarbir[CDR-Labs]]

Source of the post Hi Roman,

Any idea when 6.4 will be released. Also will it support this marvel controller.

Well,
i see they have released the Russian version in the 10th month And more then 30 to 60 odd days are over and English one is nowhere to be seen

[Roman_TS]

Well,
i see they have released the Russian version in the 10th month And more then 30 to 60 odd days are over and English one is nowhere to be seen

As soon new version will be ready, we will announce it for all our customers. If it's still not in your updateboxes then it means that our developers keep adding improvements and optimization in software part.

But even if you have the version 6.4 and PC USB Terminal ver. 3.0., there can be probably more restrictions and we find them we will also announce about them.
Now we have escalated this issue with our developers. We've had a meeting about it a few days ago and they have informed us that a complete solution with loader uploading through the SATA port will be available in 6.5 closer to the spring 2018.
This solution will be more universal and will work with all Marvel based SanDisk SSD and will not require Terminal ver.3.0.
Finally there will be two ways to recover data: partial (Terminal 3.0 and ver. 6.4x will be required) and complete (ver. 6.5x will be required).

As I've mentioned we hope that the next software update for PC-3000 SSD 6.4 will be available within approximately 2-3 weeks.
The software version 6.5 is expected to be available in the spring 2018, though no one can guarantee the exact time right now.

[Amarbir[CDR-Labs]]

Hello,
Roman Which Drives Do Have Requirements For PC Terminal Ver 3.0 And Whats The Difference in PC 3000 Terminal 2.0 And PC Terminal Ver 3.0 ,We Expect You Folks To Release a Blog or New Regarding This Small But Good Hardware Update

[Marek]

Hello Roman

Any news about Sandisk X300 model and this new adapter ver 3.0 ???

[Amarbir[CDR-Labs]]

Source of the post Hello Roman

Any news about Sandisk X300 model and this new adapter ver 3.0 ???

Marek ,
Nice to see you on forums man .They have updated this list here -> http://blog.acelab.eu.com/pc-3000-s ... dated.html .Regarding The Terminal Adapter i am of the opinion that the new one can work at higher baud rate and also might be working till 1.8 volt level

[Marek]

but the terminal is it available ?