ST340014A

[Bruno]

Hi all

I have a Seagate AT340014A, that i dont could read the data.
After start PC3000UDMA Seagate-Utility, a long time is gone, to complete the terminal entrys. Approx. 2 min.

Here is the terminal output:

Interface task reset
1024k x 16 buffer detected
ALPINE - 1_Disk M.14 01-16-03 11:51

Buzz - Head Mask 0000 - Switch to full int.
Spin Ready
3.04 06-11-03 15:19
(P)PATA Reset

CE Log EC=0 Rtype=36 OV=0 STStatus0
AutoRd Err 43 at 00f6ba.00.008b

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.008b

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.008b

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
Master
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AT Er 00 Nwt Er 47 RdWr c3b0.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 0000c1c3 ff 0000c1c3.0.000 00db 0000 e0e8 0001
AutoRd Err 47 at 00c3b0.00.01f9

CE Log EC=47 Rtype=25 OV=0 STStatus0
AutoRd Err 43 at 00f6ba.00.008b

Read Ver Retrys
SCAN Error
AutoRd Err 47 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0002

Read Ver Retrys

Read Ver Failure!
AT Er 00 Nwt Er 47 RdWr c3b0.00.0000
ATA St 50 Er 01 Op 00 0,0000/0/00,00 01 00
Niwot: 0000c1c3 ff 0000c1c3.0.000 00db 0000 e0e8 0001
AutoRd Err 47 at 00c3b0.00.01fa

CE Log EC=47 Rtype=25 OV=0 STStatus0
AutoRd Err 43 at 00f6ba.00.008b

Read Ver Retrys
AutoRd Err 43 at 00f6ba.00.0118

Read Ver Retrys
SCAN Error

What could be the problem of this HD?

Thanks for help
Bruno

[ACE_Admin]

Greetings Bruno

It is probably problem with adaptives or with the PCB. To be sure for this problem you should :

1. unscrew the pcb and check the contacts - clean them if they are dirty
2. swap the pcb with another good and compartible one, and check for terminal's output