PC-3000 Forum

Posted: **25.07.12, 08:47**

Hi All I have a Samsung SP2014N

Has a bad PCB, swapped with doner, drive powers up and starts to get ready then powers down
Here is the terminal output

lltst 0000
SpnOk
spd: 0000 0000 0000
H: +00000
ADC: 0001
DAC: A992
SK C: 0001904E
ENG>SRV>
SvoTbl Loaded
BD

FdtTbl Loaded
Sb <-------------------powers down here
WriteSctLog -- buffer not valid

Any suggestions please??

:cry:

Posted: **25.07.12, 10:22**

Is there external ROM to swap? Seems like ROM is not compatible with SA. Did you try hotswap to reach SA?

Posted: **26.07.12, 01:00**

Hey Aj,

Thanks for your reply!
No external ROM.

I tried Hotswap but didn't work for some reason, luckily if found another drive i'm going to try that now

Jason

Posted: **27.07.12, 09:53**

OVerlays and ROM should have same revision. If you cannot find ROM to match Overlays, write overlays to match ROM you do have

Posted: **28.07.12, 19:53**

jmcurtis81 wrote:Hey Aj,

Thanks for your reply!
No external ROM.

I tried Hotswap but didn't work for some reason, luckily if found another drive i'm going to try that now

Jason

Jason ,
What Was The Result ?

Posted: **30.07.12, 04:23**

Hi again,

I tried hot swap following this guide : Steps for hot-swapping all Samsung drive families: - viewtopic.php?f=33&t=6531

using the following module:

"06 CONFIG"
"10 SLISTHDR"
"11 SLIST"
"12 TLIST"
"13 ALIST"
"5D CONFIG2" (if it exist in modules table)
"62 ALISTHDR" (except PANGO, VANGOPLUS, VELOCE, RUBICON, P80A)

Still unable to see any sectors.

How do I tell if my doner is ok for hot swap? both have PV - MS on label.

Jason

Posted: **30.07.12, 10:16**

AJ2008 wrote:OVerlays and ROM should have same revision. If you cannot find ROM to match Overlays, write overlays to match ROM you do have

Posted: **30.07.12, 14:56**

jmcurtis81 wrote:Hi again,

I tried hot swap following this guide : Steps for hot-swapping all Samsung drive families: - viewtopic.php?f=33&t=6531

using the following module:

"06 CONFIG"
"10 SLISTHDR"
"11 SLIST"
"12 TLIST"
"13 ALIST"
"5D CONFIG2" (if it exist in modules table)
"62 ALISTHDR" (except PANGO, VANGOPLUS, VELOCE, RUBICON, P80A)

Still unable to see any sectors.

How do I tell if my doner is ok for hot swap? both have PV - MS on label.

Jason

Jason ,
Try What sir is Saying ,These Two Have To Match As The Overlays Are code That Has To Be Executed To complete the Process Of Initialization

Posted: **01.08.12, 08:28**

Hi again,
I think I may have jumped the gun and copied the patient drives "overlay" module onto my doner drive and now it is doing the exact same thing that the patient drive is doing :oops:

and its the only working drive like it that i have!

Have I stuffed this now? anyway to get the doner to have his overlay file back?

thanks again

Jason

Posted: **01.08.12, 10:11**

You need to reach SA access to donor and write donor overlays back. This can be achieved only through hotswap in my experience. Use a second donor to get SA access to first donor to restore.

Then write donor overlays to patient SA and use donor PCB to get user data,

Posted: **01.08.12, 17:13**

AJ2008 wrote:You need to reach SA access to donor and write donor overlays back. This can be achieved only through hotswap in my experience. Use a second donor to get SA access to first donor to restore.

Then write donor overlays to patient SA and use donor PCB to get user data,

Hello AJ2008 ,
Concentration and not rushing matters is very critical when R&D is going on .

Posted: **01.08.12, 20:51**

therepairmasters wrote:
AJ2008 wrote:You need to reach SA access to donor and write donor overlays back. This can be achieved only through hotswap in my experience. Use a second donor to get SA access to first donor to restore.

Then write donor overlays to patient SA and use donor PCB to get user data,

Hello AJ2008 ,
Concentration and not rushing matters is very critical when R&D is going on .

Sorry, but I dont understand the relevance of your statement? Is it aimed to me? :?:

Posted: **02.08.12, 07:52**

Pretty sure that was aimed at me :oops:

hehe

Ok I will try that, thanks for your advice.

as for the previous advice about the overlays, what am I doing wrong?

I wrote the patient overlay to doner HDD, which "stuffed" it.

i am only new to Pc3000 and still have many things to learn.

jason

Posted: **03.08.12, 16:04**

AJ2008 wrote:
therepairmasters wrote:
AJ2008 wrote:You need to reach SA access to donor and write donor overlays back. This can be achieved only through hotswap in my experience. Use a second donor to get SA access to first donor to restore.

Then write donor overlays to patient SA and use donor PCB to get user data,

Hello AJ2008 ,
Concentration and not rushing matters is very critical when R&D is going on .

Sorry, but I dont understand the relevance of your statement? Is it aimed to me?

Nope ,
It Was Jason :mrgreen:

.He Is a Fast Learner :mrgreen:

PC-3000 Forum

Samsung SP2014N (200 GB)

Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)

Re: Samsung SP2014N (200 GB)