PC-3000 Forum

Hello All,

Im trying Segate F3 drive with '' No HOST FIS-ReadyStatusFlags 2002B001 '' Error
Its segate ST500DM002 , FW KC48.. Im getting T..

Trying solution as mentioned https://www.youtube.com/watch?v=jWjPARPwBdk

but continuously getting LED:000000BC FAddr:00004264 error.. like below.. Can anybody tell me whats this mean /


F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>
ASCII Diag mode

F3 T>/

F3 T>V1

LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264
LED:000000BC FAddr:00004264

what is the SIM error you get, if you get one?

check PCB is original, check settings of media cache also

Hello ,

Im getting this error..



Rst 0x10M
Servo Processor Is Reset.
Spin Up
FAIL Servo Op=0100 Resp=0003
ResponseFrame FFFF 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 FFFF
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000

FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
FAIL Servo Op=0100 Resp=0003
ResponseFrame 2EB0 0603 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
No HOST FIS-ReadyStatusFlags 2002B001


PCB is original .. {Check settings of media cache also means throgh Edit HDD ID ? } Not getting entry to Edit HDD id..

Sorry - the symptoms here suggest heads cannot read. If PCB is original, I suggest you read ROM and adjust head map to test individual head (try with 0 first) .

I think it may be possible that heads are failed. Does the spindle shut down on No HOST error ?

Hello sir,

thanks for suggestions

Here are test results -->

Test : Read ROM

Reading ROM to profile folder
Folder: C:\Program Files (x86)\ACE Lab\PC-3000\Bin\!Profiles\SgF3\F3 Arch (common)\KC48 TEST\Data\ROM\
File : ROM.bin
Error : DT ID 15 is not found!
Result.................................. : Error




Head Map Test shows--->

SetKey error!
start time 7/15/2015 11:23:33 AM
finish time 7/15/2015 11:25:11 AM


I think its confirm head problem..

- VaibhavS