PC-3000 Forum

HAI ALL,

i have one Seagate HDD Model:ST500DM002 , FW:KC45. It showing Capaity ,model,serial everything showing properly. When i enter into the Utility (Ctrl+Z) it showing the following Messages.



F3 T>
Boot 0x10M
Spin Up[0x00000000][0x0000B67C][0x0000BA10]
Trans.

Rst 0x10M
MC Internal LPC Process
Spin Up
(P) SATA Reset

InitiateMarkPendingReallocateRequest for disc_lba: 00136BD4!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BD5!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BD6!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BD7!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BD8!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BD9!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDA!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDB!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDC!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDD!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDE!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BDF!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE0!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE1!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE2!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE3!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE4!
InitiateMarkPendingReallocateRequest for disc_lba: 00136BE5!
ASCII Diag mode


What type of error is showing ? and how I can solve it?

HELP me

CONGEN

THANKU

Please explain more

How it works and where I should use this command . ie F3 T > ,after/before etc


betty
crystal

Hai all,

I have tried Recover Translator. then i was getting this terminal output


Test : Recover translator
Start from LBA.................................... : 0
Translation "forks" list file..................... : C:\Program Files\ACE Lab\PC-3000\Bin\!Profiles\SgF3\F3 Arch (common)\ST500DM002-1BD142-KC45-S2AA7WRQ\Defects\TranslationForks.lba
Maximal defect chain length....................... : 64
Take into account P-List.......................... : Yes
At ambiguity hide "left" UNC...................... : Yes
Process "32 byte tail" bug........................ : Yes

HDD ID reading...
Detecting defects hiding cmd type...
Error detecting defects hiding cmd type!

hai to all


the terminal out put of same HDD is like this:

Dither
Dither
Dither
Dither
Dither
Dither
Dither
Dither
Dither
Dither
Dither
Dither



Any one have any idea , please share with me

Probably this drive will reach ready condition by itself after some time.

Problem is relocation process is with errors meaning the process of relocating bad blocks is causing issues, or alt list is full.

Translator recovery will not help.

Access settings udner 'HDD ID' and uncheck all boxes.

also, it is very dangerous to try different commands in the wrong circumstances, such as translator recovery when translator is fine as this will clear NRG and Glist and there is no certainty that it can restore successful with no manual intervention