PC-3000 Forum

Tech Key...
Requesting FW Pkg ver ........ PH0G7B.CCD3.BZ1E2H.

Collecting Sys Files Infos...
ID Len
===============
0 4
1 2
2 16
3 3787
4 12
5 4
6 66
7 1
8 4800
9 1
A 2251
B 1000
C 64000
D 160
E 432
F 223
13 8
15 100
16 2
17 40
19 24
1A 33
1B 1
1C 9
1D 128
1E 128
1F 640
22 80
23 80
24 80
25 80
26 80
27 80
28 80
29 80
2A 9
2B 1172
2C 432
2D 432
2E 432
2F 432
30 432
31 432
32 432
33 4576
34 640
35 26
3A 4
Collecting Sys File Infos completed

Collecting CP Infos...
ROM:
ID MemOffs Len
==========================
0 6037200 33792
1 6037000 512
4 4002C00 4096
602BE00 4096
total 8192
5 6C000 81920
8 40070000 948
A 60B48E0 2048
12 400D4000 196
13 60C0AC0 864
14 60C0E20 96
15 0 524288
1B 60BE8C4 8700
1C 60BE784 320
1D 6037220 352
1E 60374B0 2416

RAM:
ID MemOffs Len
==========================
0 6037200 33792
1 6037000 512
2 6037380 304
4 4002C00 4096
602BE00 4096
total 8192
5 6C000 81920
6 277E44 40996
8 40070000 948
A 60B48E0 2048
12 400D4000 196
13 60C0AC0 864
14 60C0E20 96
15 0 524288
16 6037200 32
17 6039240 1216
1B 60BE8C4 8700
1C 60BE784 320
1D 6037220 352
1E 60374B0 2416
1F 6184670 1224
20 6184B38 72


WARNING! It`s probably HDD have "Translatioin violation (0 GB)" problem
Try the command: Solution for problem "Translation violation (0 GB)"
From menu: Tests -> Solutions
Collecting CP Infos completed


Tried User Command - Clear SMART - Terminal : reply timeout error (tried manualy with N1 but same result)


T>V1
User Slip Defect List
log log log phys phys
LBA span cumm cyl hd sctr zn cyl sctr SFI PBA
0 0 0 0 0 0 0 0 0 4 0

Head 0: entries 1 slips 0
Head 1: entries 0 slips 0
Head 2: entries 0 slips 0
Head 3: entries 0 slips 0
Total Entries 1 Total Slips 0


Tried Isolate motor
F3 T>/2

F3 2>Z

ExecuteSpinRequest
HighPowerMode = 0100
DiagError 00006002
F3 2>U

ExecuteSpinRequest
Spin Up Complete
Elapsed Time 6.424 secs
F3 2>/1

F3 1>N1

Init SMART Fail
LED:000000CC FAddr:0024EDB5
LED:000000CC FAddr:0024EDB5

Any ideas welcome - Thanks

Hi

Try to perform next steps:
run utility
turn power on
wait ready state
ctrl+z
spin down
spin up
regenerate translator (from user commands menu or manually)
clear smart.
Paste here log if you will not get success.

Spin Down Complete
Elapsed Time 511.291 msecs
F3 2>U

ExecuteSpinRequest
ExecuteSpinRequest
HighPowerMode = 0100
Spin Up Complete
Elapsed Time 6.344 secs
F3 2>
ASCII Diag mode

F3 T>/

F3 T>m0,6,2,,,,,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 16, Max Certify Rewrite Retries = 2DF8

Init SMART Fail
LED:000000CC FAddr:0024EDB5
LED:000000CC FAddr:0024EDB5

Much of the 7200.12 series require short circuit to allow translator to rebuild...

DatalabNZ wrote:Spin Down Complete
Elapsed Time 511.291 msecs
F3 2>U

ExecuteSpinRequest
ExecuteSpinRequest
HighPowerMode = 0100
Spin Up Complete
Elapsed Time 6.344 secs
F3 2>
ASCII Diag mode

F3 T>/

F3 T>m0,6,2,,,,,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 16, Max Certify Rewrite Retries = 2DF8

Init SMART Fail
LED:000000CC FAddr:0024EDB5
LED:000000CC FAddr:0024EDB5

clear Smart then Trans. Reg.

and post the log here again for this process

With read channel shorted
F3 1>N1

Failed to load overlay 00000004
LED:000000CC FAddr:0028540B
LED:000000CC FAddr:0028540B



With read channel shorted
F3 T>m0,6,2,,,,,22
Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 16, Max Certify Rewrite Retries = 2DF8

Init SMART Fail
LED:000000CC FAddr:0024EDB5
LED:000000CC FAddr:0024EDB5

Hi,
I too have the exactly same problem on a CC44 firmware ST3250318AS (7200.12)

SMART clearing command gives LED error in terminal. I am trying to copy the SMART module from similar drive and trying to clear afterwards.

Will update later. Any more ideas?

Mathew

No luck on this drive yet

Mahew

mvg wrote:No luck on this drive yet

Mahew

Hello

If you see LEDCC error after trying to clear smart, it may mean that heads are bad.

Is this solved yet?

If not send me PM with skype name (if you have), maybe I can help.