Seagate Momentus 5400 FDE.2

[DR_Ireland]

I got the drive which is encrypted (that is what the owner says). I connect to PC3000 and it will come up ready but the max LBA is not showing. It will show only a part of the max LBA and the size is 128MB. What can be the problem here and how to solve it?

Model: ST980816AS / Firmware: 3.ADB

Any suggestions?

[AJ2008]

I got the drive which is encrypted (that is what the owner says). I connect to PC3000 and it will come up ready but the max LBA is not showing. It will show only a part of the max LBA and the size is 128MB. What can be the problem here and how to solve it?

Model: ST980816AS / Firmware: 3.ADB

Any suggestions?

I think with this HDD the encryption is at a SA level.

[Amarbir[CDR-Labs]]

I got the drive which is encrypted (that is what the owner says). I connect to PC3000 and it will come up ready but the max LBA is not showing. It will show only a part of the max LBA and the size is 128MB. What can be the problem here and how to solve it?

Model: ST980816AS / Firmware: 3.ADB

Any suggestions?

I think with this HDD the encryption is at a SA level.

Well ,
Seagate Is Bend Upon Making Our Life Hell

Regards

Amarbir @ HDDGURU

[labtech]

I believe that terminal is disabled in these drives, so the Seagate utility will not work

[AJ2008]

Safe Mode works, but is restricted a little.

[avenger-fr]

Excuse me, but for me I haven't Safe mode (F3 series) and when we would access in terminal I have

>(1Ah)-Serial Port Disabled

I have make a video of my little tool for break the problem with FDE who are "Trusted" (not ATA password but fully encrypted). You can see at http://www.hddsync.com/services/unlock-fde/

Maybe you need this (if you have the USER password)...

[avenger-fr]

Ps : We can't access to SA on this disk , I have just read ID page , nothing else ...

You can see the log :

Collecting Sys Files Infos...
Error collecting Sys File Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting Sys File Infos completed

Collecting CP Infos...
Error collecting CP Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting CP Infos completed

Soft reset ...
Collecting Sys Files Infos...
Error collecting Sys File Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting Sys File Infos completed

Collecting CP Infos...
Error collecting CP Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting CP Infos completed

Soft reset ...


Test : Reading ROM

Reading ROM to profile folder
Folder: C:\Program Files\ACE Lab\PC-3000\Bin\!Profiles\SgF3\F3 Arch (common)\ST9250424ASG-DEC6-5TH0M05A\Data\ROM\
Error : CP ID 15 is not found!
Result............................................ : Error


Test : Modules reading


Test : CP reading
CPs are not selected
Requesting FW Pkg ver ........
CA0AC2.DEM2.CA201S.DEC6


Test : Modules reading


Test : Modules reading
Modules are not selected
Recalibration attempt ...
Ok

Soft reset ...
Hard reset ...
Collecting Sys Files Infos...
Error collecting Sys File Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting Sys File Infos completed

Collecting CP Infos...
Error collecting CP Infos!
Error : Error requesting command state "En Tech" (<bit3>)
Collecting CP Infos completed

Soft reset ...
Terminal : error detecting HDD terminal baud rate
Error switching COM port baud rate

[Vikas]

Hi
I came with the same hard disk, but I repaired it and then from Seagate Casing itself I have recovered the data.

Vikas