SM2259XT New Loader

[p4xel]

Hi. I got a Netac SA500 SSD with SM2259XT2G controller chip and cannot find a loader for it in the utility

When it starts it picks FIM38B_00 loader, and after initial stage shows:

Code: Select all

Loader uploading
****************************************
   Power Off
   Power On
   Ready state waiting..................... : Ok
   Safe mode............................... : Ok
   MPISP code name......................... : W0825A0 FIMN38_00 (XT2); W0621A(N)
   
   W0825A0 FIMN38_00 (XT2); W0621A(N)...... : Ok
   Calling executable code................. : Ok
   
   Seed table reading
   Completed
   Microcode reading (0)................... : Ok
   Firmware version (Internal)............. : X0419B0 FIM38B_00
   SSD parameters reading.................. : Ok
   Loader not found by internal name.
   Search for compatible loaders...
   Loader is not uploaded! Some utility functions may not work properly!
   
   SSD status:
   SSD is in ready state................... : Yes
   Firmware mode........................... : LDR
   SSD error code.......................... : 0x00 (No errors)
   SSD is locked........................... : No
   SSD is in Safe Mode..................... : No
   Logical access is possible.............. : No
   Physical access is possible............. : Possibly
****************************************
Test completed
Drive power supply...................... : OFF

But I don't see X0419B0 FIM38B_00 on the list, and if I select anything else it fails.


NAND chips:

Code: Select all

System Info:
Chips id................................ : 89D3AC32C204
Vendor.................................. : Intel
Type.................................... : 144L(N38) QLC 16k
Chip capacity........................... : 144 000 Mb
Channels................................ : 2
Chips (Total)........................... : 0x04
Planes per chip......................... : 4
LUNs per chip........................... : 1
Blocks per chip......................... : 0x00FA
Pages per block......................... : 0x9000
Page size............................... : 0x4000
Max retry level......................... : 0x00

Any help apreciated.

[italyassistance]

Selection N38, and try all loader N38, if dont fuction your ssd have particular firmware but it is strange same standard SM2259XT2, u ask at TS team?

[p4xel]

I tried many of them (IMN38, FIMN38 and EIMN38)

And not getting much success results with errors like


Calling executable code................. : Ok
Microchips information uploading........ : Command execution error; Read sector error (LBA: 21 930); HDD DMA RQ timeout (10000)

-------------------------------------------------------------------------------------------------------

Calling executable code................. : Ok

Seed table reading
Completed
Microcode reading (0)................... : Ok
Firmware version (Internal)............. : O¾2 <-- FW version invalid
SSD parameters reading.................. : Ok
Loader not found by internal name.
Search for compatible loaders...
Loader is not uploaded! Some utility functions may not work properly!

-------------------------------------------------------------------------------------------------------

MPISP code name......................... : W0306B0 FIMN38_00 (XT2); W0308A(N)

W0306B0 FIMN38_00 (XT2); W0308A(N)...... : Ok
Calling executable code................. : Ok

Seed table reading
Completed
Microcode reading (0)................... : Ok
Firmware version (Internal)............. : X0419B0 FIM38B_00
SSD parameters reading.................. : Ok
Loader not found by internal name.
Search for compatible loaders...
Loader is not uploaded! Some utility functions may not work properly!


It displayed the same loader selection window again, I selected the same loader and it started (kind of)
I am trying to create Translator. Will see how it goes.

[p4xel]

I built the translator but when trying to read sectors in task I get those everywhere

Code: Select all

LBA 0; block: 0x0049; page: 0xAC87; Page marker checking error
LBA 8 696; block: 0x0052; page: 0x1CC2F; Page marker checking error
LBA 179 069 957; block: 0x00C2; page: 0x71CC; Page marker checking error
LBA 318 485 197; block: 0x00E8; page: 0xFC98; Page marker checking error


[italyassistance]

version of software?