PC-3000 Forum

I am just uploading this cases for the future updates of PC3000

DSS Digital surveillance system SSD from Dahua
Using SM2259XT controller

Model : SM59XT2A-80-50000001
Serial : (03)5526888-20080228
Firmware : 20210308
Capacity : 1 GB (2 096 640)

Selected family......................... : Silicon Power Slim S55 (SM2259XT)
Controller.............................. : SM2259XT

SSD status:
SSD is in ready state................... : Yes
Firmware mode........................... : ROM
SSD error code.......................... : 0x00 (No errors)
SSD is locked........................... : No
SSD is in Safe Mode..................... : Yes
Logical access is possible.............. : No
Physical access is possible............. : No

Chips id................................ : 453E98037664
Vendor.................................. : Sandisk
Type.................................... : 112L BiCS5 TLC 16k

Loader uploading
****************************************
MPISP code name......................... : U1124A0 FBiCS5_06 (XT2); U0915A(N)

U1124A0 FBiCS5_06 (XT2); U0915A(N)...... : Ok
Calling executable code................. : Ok

Seed table reading
Completed
Microcode reading (0)................... : Ok
Firmware version (Internal)............. : U1224A0 FBiCS5_08
SSD parameters reading.................. : Ok
Loader not found by internal name.
Search for compatible loaders...

Ready state waiting..................... : Ok
U0916A0 FBiCS5_06 (XT2); U0915A(N)...... : Ok
Calling executable code................. : Ok

Reset SSD controller.................... : Ok
Config Package.......................... : Ok
U0916A0 FBiCS5_06 (XT2); Q0209(D)....... : Ok
Calling executable code................. : Ok
Invalid FW mode 5 (0)

SSD status:
SSD is in ready state................... : No
Firmware mode........................... : Unknown
SSD is locked........................... : Unknown
SSD is in Safe Mode..................... : Unknown
Logical access is possible.............. : No
Physical access is possible............. : No
Operation aborted
****************************************
Loader is not uploaded! Some of the functions are not available!
Utility initialization was terminate!

Sandisk BiCS5 support will appear in the upcoming update. But again, I want to remind you that PC-3000 Forum - is the place where ACELab customers are able to communicate with each other. If you need a help with case support, please contact ts.acelab.eu.com

Same problem here! Invalid FW mode 5 (0) iv selected the firmware suggested by the utility but i get Invalid FW mode 5 (0) ! sometime i can rebuild the translator but serial number and capacity doesnt change! im stuck

Passport ID in Utility means nothing. It always shows you the default template, no matter what is the real capacity of the drive. You can see the real capacity only in DE when you make a new task.

Roman_TS wrote:Source of the post Passport ID in Utility means nothing. It always shows you the default template, no matter what is the real capacity of the drive. You can see the real capacity only in DE when you make a new task.

thank you Roman! but the guide is not clear and i still get Invalid FW mode 5 (0) when i select the loader! should i keep shorted ? should i check on SAFE MODE?

Here is the guide about correct loader uploading:

https://blog.acelab.eu.com/pc-3000-ssd- ... t-xt2.html

If your internal drive firmware 100% compatible with the loader, but you got some issues with the final drive initialization - ask your customer about the story of this drive. Probably SSD was formatted, or customer already tried to update FW by himself.

Roman_TS wrote:Here is the guide about correct loader uploading:

https://blog.acelab.eu.com/pc-3000-ssd- ... t-xt2.html

If your internal drive firmware 100% compatible with the loader, but you got some issues with the final drive initialization - ask your customer about the story of this drive. Probably SSD was formatted, or customer already tried to update FW by himself.

The guide you gave me doesnt work properly! the utility finds the loader but it doesnt work.....



Loader uploading
****************************************
MPISP code name......................... : U0916A0 FBiCS5_06 (XT2); U0915A(N)

U0916A0 FBiCS5_06 (XT2); U0915A(N)...... : Ok
Calling executable code................. : Ok

Seed table reading
Page reading (channel: 0; chip: 0; block: 0x0000; page: 0x0004); ECC error
Completed
Microcode reading (0)................... : Ok
Firmware version (Internal)............. : V0111A0 FBiCS5_08
SSD parameters reading.................. : Ok

Ready state waiting..................... : Ok
V0111A0 FBiCS5_08 (XT2); V0107A(N)...... : Ok
Calling executable code................. : Ok

Reset SSD controller.................... : Ok
Config Package.......................... : Ok
V0111A0 FBiCS5_08 (XT2); Q0209(D)....... : Ok
Calling executable code................. : Ok
Invalid FW mode 5 (0)

SSD status:
SSD is in ready state................... : No
Firmware mode........................... : Unknown
SSD is locked........................... : Unknown
SSD is in Safe Mode..................... : Unknown
Logical access is possible.............. : No
Physical access is possible............. : No
Operation aborted
****************************************
Loader is not uploaded! Some of the functions are not available!
Utility initialization was terminate!

Make sure that all NAND chips IDs are reading fine. There could be a hardware problem with this SSD.

Also, you can try to check neighbour loaders with similar V01XXXX FBiCS5_08 family.