PC-3000 Forum

Posted: **14.10.17, 09:46**

I have a WD 2 TB model WD 20 NMVW.
I had shifted the region.
Now can not go back. Whenever I a doing allow SA region, still it shows region shifted.
Can someone help how to have the region address.

ROM version............................. : 21.3RH
ROM generation.......................... : 21.3RH
Link table version...................... : N0.41.
Consolidated ROM version................ : 0021003R

ROM Modules:
Flash ROM dir reading................... : Ok
Flash ROM dir reading (Ext)............. : Ok (Active)
Modules directory address............... : 318 128
SA regions address...................... : shifted
SA Translator loading................... : Ok
SA defects assigned..................... : 1

Heads configuration..................... : by map
Heads number............................ : 8
Heads number in use..................... : 8
Switched off heads...................... : No
Heads map............................... : 0,1,2,3,4,5,6,7
ROM Firmware version.................... : 0021003R

Thanks

Posted: **17.10.17, 20:48**

Can't you write back the original ROM?

Posted: **19.10.17, 02:12**

Are you running the shift in Ram or in Rom?
For me you are working in Ram, and you must shift the regions in Rom

Posted: **19.10.17, 13:29**

Imnew, go to Work with ROM->Allow SA access and restart HDD menu.

Posted: **19.10.17, 18:18**

Imnew wrote:Source of the post I have a WD 2 TB model WD 20 NMVW.
I had shifted the region.
Now can not go back. Whenever I a doing allow SA region, still it shows region shifted.
Can someone help how to have the region address.

ROM version............................. : 21.3RH
ROM generation.......................... : 21.3RH
Link table version...................... : N0.41.
Consolidated ROM version................ : 0021003R

ROM Modules:
Flash ROM dir reading................... : Ok
Flash ROM dir reading (Ext)............. : Ok (Active)
Modules directory address............... : 318 128
SA regions address...................... : shifted
SA Translator loading................... : Ok
SA defects assigned..................... : 1

Heads configuration..................... : by map
Heads number............................ : 8
Heads number in use..................... : 8
Switched off heads...................... : No
Heads map............................... : 0,1,2,3,4,5,6,7
ROM Firmware version.................... : 0021003R

Thanks

Well,
The Basic Strategy I Use For Backup Is As Following ,I Enter The Utility In Kernel Mode And Read Rom And Rom Modules Then i Quit Utility Enter Inside Utility again And Read Modules In ABA Mode of Different Heads And Make New Profile ,Like This i Have Two Profiles Of One Drive With ROM And Rom Modules in One And ABA Accessed Modules In Second One .Like This i Have Entire SA With Me And Can Undo Anything .In Your Case You Should Undo This Process By Writing Back Initial Saved Rom Or Using What Maxim Tells You [ though There Are Two Methods To Undo This In Tool ] . BTW Acelab TS Guys The Earlier Version Had " Shifted " Written in Red and It Was So Easy To See this Can You Ask Developers To Change Colour If Shifted To Red In The Very Next Update You Fellows Make .

Posted: **27.10.17, 18:00**

Amarbir[CDR-Labs] wrote:Source of the post BTW Acelab TS Guys The Earlier Version Had " Shifted " Written in Red and It Was So Easy To See this Can You Ask Developers To Change Colour If Shifted

It will be marked red in next 6.4 version

Posted: **27.10.17, 19:02**

Maxim,
i would say that good features of one version should be retained in all further versions like this colour thing cheers mate

PC-3000 Forum

SA region address can not be shifted back

SA region address can not be shifted back

Re: SA region address can not be shifted back

Re: SA region address can not be shifted back

Re: SA region address can not be shifted back

Re: SA region address can not be shifted back

Re: SA region address can not be shifted back

Re: SA region address can not be shifted back